For implementing DNC and SHOPlink software

 4/8/16 Port Controller Card, NPORT servers, Wireless servers

  Optical Isolators High /Low speed  

 Line drivers & protocol converters, RS422,RS485,20mA 

 BTR-RE93 : Tape reader emulators

 Ethernet to serial converters 

 RS 232 cables and connectors 

 Diagnostics connectors & utilities

 Machine monitoring device

 Machine monitoring device-HMI

 4/8/16 Port controller card

          Wireless Access Point (Near DNC)

             Wireless Node (Near CNC)

           Nport server in sizes of 4 /8/16 ports                                                                                                                             Top

OPTICAL ISOLATOR

The Optical Isolator unit is used to protect the Serial Ports(RS232) from the damage, due to following causes:

1) Floating voltages on communication lines.

2) Spikes.

3) Leakage current.

4) And due to ground problems, etc.

LOW SPEED

HIGH SPEED

FEATURES

Its having the spike suppressor.

Optically isolates the grounds between two ports .

Optically isolates the other all signals that are required for the communication with CNC & other applications

mproves strength of signal level .

Filters RF & high voltage spikes

Baud rate upto 115200

APPLICATIONS

DNC systems

PLC application.

And in all other application where the communication is done through serial port

SPECIFICATION

Its requires AC 230V,5A with good earth connection.

It isolates Tx/Rx/CTS/RTS.                                                                                                                                         Top

BTR-RE93 : Tape reader emulators

RE 93 is Electronic paper taper reader emulator for direct replacement of paper tape readers and punchers. It has got micro controller CPU for handling various protocols in CNC communication. It has electronic memory for storing NC data and Executable software. It has optically isolated RS232 port for PC communication

INTERFACE

RE 93 has standard RS 232 port for PC communication. It has transmit and receive line and has Xon Xoff protocol. RS 422 also can be incorporated with one additional converter. RS 232 port of RE 93 is optically isolated from ground.

For Reader / Punchar connection RE 93 has two ports called input port and output port. Both are 25 pin D type connectors. Input port is for connecting existing reader. If reader is connected to this port, paper tape can be read and store into RE 93 memory. If puncher port from CNC is connected to this port, NC data sent by CNC to puncher port will be collected by RE 93 and store electronically. Data stored in RE 93 can be later sent to PC using RS 232 port.

RE 93 has output port for connecting to reader port of CNC or puncher. RE 93 can respond to CNC exactly as reader responds to CNC and send NC data to CNC electronically. It generates sprocket signal for certification. If puncher is connected to this port RE 93 will drive puncher so that paper tape can be punched out.

RE 93 can emulate following interfaces as on today and can be configured for any other interface if necessary timing diagrams are available with the customers.

FANUC Reader

Tally Reader

Acrared Reader

Gilmetti Reader

General Electric

SlO Syn Reader

GNT Reader

Remex Reader

FER 202 Reader (AGIE)

Facit Reader

GNT Puncher

Excellon CNC 6

Fanuc 6M - With BTR RE93 block by block communication can be achieved. This facility is not available with   

   RS232 port available on machine

JAPAX - Japax machines are fitted with Cassette for data transfer. Cassette can be eliminated with RE93

AGIE CNC wire EDM

CMM

OKK

Okuma

Pratt & Whitney

Sieb and Mayor : PCB drill machines                                                                                                          Top 

  CUSTOMERS

  Includes Godrej, L&T, M&M, Siemens, GKN, BHEL, HAL, DRDL, Circuit systems, Escorts, Rasandik, Tecumsh,  

  Crompton

Home   |   DNC    |    CADlink    |    ANACAM     |    Machine Monitoring   |     Solid-Edge    |    Resellers   |    Contact    |      Download